Holybro Kakute F7 Mini V3 + Tekko32 F3 45A 4in1 + Atlatl HV micro 800mW VTX

The Mini Kakute F7 V3 Stack by Holybro comes with the Kakute F7 Mini V3, Tekko32 F3 4in1 mini ESC(45A), and the Atlatl HV Micro VTX. Holybro is saving you time and guesswork by making this powerful stack that will give you max performance and great video quality!

Specifications

Kakute F7 mini V3

Specifications

• MCU: STM32F722RET6 32-bit processor,216MHz, 256Kbytes RAM, 512Kbytes Flash
• IMU: MPU6000 (SPI)
• Barometer: BMP280
• USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
• 5hardware UARTS (UART1,2,3,4,6)
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
• Onboard 16Mbytes for Blackbox logging
• 5V Power Out: 1.0A max
• 3.3V Power Out: 0.2A max
• Dimensions: 30x30mm
• Mounting Holes: Standard 20mm square to the center of holes
• Weight: 4g

Pinout Diagram

Tekko32 F3 4in1 mini ESC(45A)

The latest Tekko32 F3 4in1 mini ESC has got some improvements on its performance

The PCB design uses a design in which the drive circuit and the control circuit are separated. This design broadens the overcurrent capability of the drive circuit, and at the same time reduces the electrical interference to the control circuit.

BLHELI32 / F3 MCU/4x 45A

The New BLHELI32 ESC adapted the F3 MCU, which will provide a smoother control and faster response speed,
4x 45A F3 BLHELI32 ESC in 20x20 standard.

Specifications

• F3 MCU, double the speed of F051
• 32bit ESC with BLHELI32 firmware
• Supports 3-6S Lipo input
• Default PWM output 96K
• The amperage meter scale ratio has been adjusted to 185.
• PWM input, TLM supported
• Voltage output (VBAT)
• NO output BEC
• Supports Oneshot / Multishot / Dshot PWM
• Supports damped light
• Ext. cap needed for 6s (1000uf 35v for 6s usage.)
• Mounting holes: 20x20mm(M3)
• Size:32 x 38 mm
• Weight: 8g

PIN MAP

Atlatl HV Micro VTX

Features

• Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
• Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
• SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
• All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.
• MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.
• LED indicators for channel, band, and power. Allows easy check of VTX parameters simply by glancing at the quad.
• Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
• 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
• Built-in microphone, so you can listen to your motors while you fly, no matter how far away you fly.
• The standard 26mm form factor allows you to mount the Atlatl directly on your flight controller stack.

Specifications

• Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
• Audio: 6.5 MHz Mono
• Protocol：smart audio2.0
• Antenna Connector: MMCX
• Input Voltage: 7 to 28 volts (2-6S LiPo)
• Dimensions: 30x26mm
• Mounting Holes: Standard 20mm square to center of holes (M3)
• Weight: 3.6g

Includes

• Kakute F7 mini V3 STACK *1
• Electrolytic capacito: 1000uF 35v *1
• 8pin to 8pin 1mm pitch 65mm cable *1
• 8pin to 8pin 1mm pitch 25mm cable *1
• JST SH 6pin 150mm cable*1 ( The cable that goes to the CADDX Vista Air Unit is included.)
• JST GHR 8pin to JST GHR 6pin 80mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
• JST GHR 8pin to JST GHR 6pin 150mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
• 80mm SMA--MMCX Cable *1
• 60mm Antenna *1
• 150mm 4pin JST GH wire *1

Manuals

• Kakute F7 mini V3 Manual
• Holybro_Atlatl_HV_micro_Manual
• Tekko32 F3 4in1 mini ESC(45A)

Some Tips

• BLHeli_32 ESC Firmware Overview
• GitHub

Download

• ATLATL HV V2-VTx Table