1. Do not recharge the battery when you are away from home, do not charge the battery immediately after flying, do not over-discharge the battery. (Over-discharge may cause the battery to fail to charge and become useless) Turn off the power immediately after the battery is fully charged. Please do not charge the battery for a long time.

2. Do not modify any parameters and wiring without knowing the flight control and remote control.

3. Before powering on the airplane, please turn on the remote control first, unplug the power switch after the flight, and then turn off the remote control to prevent accidents.

4. The product has been welded. If you have any technical and assembly problems, please feel free to contact us. We have a dedicated technical team to answer related questions.

5. This product is not a toy and is not suitable for children under 14 years of age.

6. If you are a beginner, it is recommended to be assisted by an experienced adult.

7. Novices should pay attention not to hold the airplane with your hands when the airplane is turning, and don't let children touch it. Prevent being scratched.

8. Please turn off the start switch in time when the plane falls from a wall or hits other objects at a high altitude during flight. Otherwise, it may cause damage to the flight controller and motor. Please take off after checking that the aircraft is not damaged and the screws are not loose.

Functions and features:

Wheelbase: 135mm

Built-in OSD Betaflight

Support BLHeliSuit configuration

Support voltage 2-3S

Remote control distance: FLYSKY remote control is about 300 meters, T-lite remote control is about 2000 meters

Battery life is about 5 minutes

Paddle

Type: 3016

Number of leaves: 3 leaves

Size: 3inch

Material: PC

Weight/g: 1.18g

Integrated ESC and flight control:

Size: 32.5x32.5mm

Mounting hole: 25.5x25.5mm

Weight: 7.3g

CPU: STM32F411CEU6 (100MHZ)

Main control board: MPU6000 (SPI)

Firmware: Betaflight JHEF411

Integrated OSD Betaflight (AT7456E)

BEC output (two): 9V/2A, 5V2.5A

Receiver: SBUS, IBUS, DSM2, DSMX, TBS (UART2)

Black box: 8MB

Built-in current sensor

Input voltage: 2-6S Lipo

ESC current: 25a

Firmware: BLHELI_S GH-30.HEX

Support PWM, Oneshot42, Oneshot125, Multishot, Dshot150 and Dshot300, Dshot600

Image transmission:

Project name: 5.8G 40CH 25mW 100mW 200mW switchable FPV transmitter

Input voltage: 4.5-5.2V (DC)

Input current: 500mA @ 200mW

Power: 25mW / 100mW / 200mW (switchable)

Channel: 40CH

Antenna connector: IPEX

Size: 37x24x5mm

Mounting hole: 25.5x25.5mm

Motor:

Specification: 1204

KV option: KV5000

Configuration: 9N12P

Stator diameter: 12mm

Stator length: 4mm

Inner shaft diameter: Φ2mm

Outer shaft diameter: Φ1.5mm

Motor size (diameter * lens): Φ15mm * 16.2mm

Weight (g): 5.9g

Support voltage: 2-4S

Camera:

Lens: 1.8mm

Aspect ratio: 16:9

Resolution: 1200TVL

Input voltage: DC3.7V-18V

Weight: 2g

Installation size: 14mm/19mm

Receiver version: FRSKY version, FLYSKY version, without receiving version

Q&A

Please refer to our pictures to choose the desired combination, all parts are sold separately in our shop, and you can add them as spares. If you have any questions, please feel free to contact us.

F23184(1).jpg